200-125 Dumps 200-125 Exam Questions 200-125 New Questions 200-125 PDF 200-125 VCE Cisco

[2017-Dec-New] Lead2pass 100% Valid 200-125 Exam Questions PDF Free Download (356-365)

There is no need to hassle if you are stuck in the 200-125 exam difficulties, Lead2pass will assist you right through 200-125 exam with 200-125 PDF and VCE dumps. Lead2pass delivers the most comprehensive 200-125 exam dumps, covering each and every aspect of 200-125 exam curriculum. We ensure you 100% success in 200-125 exam.

Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/200-125.html

QUESTION 356
Which pairing reflects a correct protocol-and-metric relationship?

A.    OSPF and mumber of hops and reliability
B.    EIGRP and link cost
C.    IS-IS and delay and reliability
D.    RIPv2 and number of hops

Answer: D

QUESTION 357
Refer to the exhibit, The VLAN configuration of S1 is not being in this VTP enabled environment. The VTP and uplink port configurations for each switch are displayed. Which two command sets, if issued, resolve this failure and allow VTP to operate as expected?(choose two)

3571
A.    S2(config)#vtp mode transparent
B.    S1(config)#vtp mode client
C.    S2(config)#interface f0/24
S2(config-if)#switchport mode access
S2(config-if)#end
D.    S2(config)#vtp mode client
E.    S1(config)#interface f0/24
S1(config-if)#switchport mode trunk
S1(config-if)#end

Answer: BE

QUESTION 358
How are VTP advertisements delivered to switches across the network?

A.    anycast frames
B.    multicast frames
C.    broadcast frames
D.    unicast frames

Answer: B

QUESTION 359
Refer to the exhibit. What could be possible causes for the “Serial0/0 is down” interface status? (Choose two.)

3591

A.    A Layer 1 problem exists.
B.    The bandwidth is set too low.
C.    A protocol mismatch exists.
D.    An incorrect cable is being used.
E.    There is an incorrect IP address on the Serial 0/0 interface.

Answer: AD

QUESTION 360
Refer to the exhibit. Which two statements are true about the loopback address that is configured on RouterB? (Choose two.)

3601

A.    It ensures that data will be forwarded by RouterB.
B.    It provides stability for the OSPF process on RouterB.
C.    It specifies that the router ID for RouterB should be 10.0.0.1.
D.    It decreases the metric for routes that are advertised from RouterB.
E.    It indicates that RouterB should be elected the DR for the LAN.

Answer: BC

QUESTION 361
A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration? (Choose three.)

A.    A switch in the VTP client mode cannot update its local VLAN database.
B.    A trunk link must be configured between the switches to forward VTP updates.
C.    A switch in the VTP server mode can update a switch in the VTP transparent mode.
D.    A switch in the VTP transparent mode will forward updates that it receives to other switches.
E.    A switch in the VTP server mode only updates switches in the VTP client mode that have a higher
VTP revision number.
F.    A switch in the VTP server mode will update switches in the VTP client mode regardless of the
configured VTP domain membership.

Answer: ABD

QUESTION 362
Refer to the exhibit. Both switches are using a default configuration. Which two destination addresses will host 4 use to send data to host 1? (Choose two.)

3621

A.    the IP address of host 1
B.    the IP address of host 4
C.    the MAC address of host 1
D.    the MAC address of host 4
E.    the MAC address of the Fa0/0 interface of the R1 router
F.    the MAC address of the Fa0/1 interface of the R1 router

Answer: AF

QUESTION 363
What are two reasons a network administrator would use CDP? (Choose two.)

A.    to verify the type of cable interconnecting two devices
B.    to determine the status of network services on a remote device
C.    to obtain VLAN information from directly connected switches
D.    to verify Layer 2 connectivity between two devices when Layer 3 fails
E.    to obtain the IP address of a connected device in order to telnet to the device
F.    to determine the status of the routing protocols between directly connected routers

Answer: DE

QUESTION 364
Refer to the exhibit. The router has been configured with these commands:
3641

What are the two results of this configuration? (Choose two.)

3642

A.    The default route should have a next hop address of 64.100.0.3.
B.    Hosts on the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C.    The address of the subnet segment with the WWW server will support seven more servers.
D.    The addressing scheme allows users on the Internet to access the WWW server.
E.    Hosts on the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet
without address translation.

Answer: DE

QUESTION 365
A company is installing IP phones. The phones and office computers connect to the same device. To ensure maximum throughput for the phone data, the company needs to make sure that the phone traffic is on a different network from that of the office computer data traffic. What is the best network device to which to directly connect the phones and computers, and what technology should be implemented on this device? (Choose two.)

A.    hub
B.    router
C.    switch
D.    STP
E.    subinterfaces
F.    VLAN

Answer: CF

More free Lead2pass 200-125 exam new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDM0s1aXlFTXBWdGM

We highly recommend our 200-125 dumps. Comparing with others’, Lead2pass is the most credible and authentic source of information on 200-125 exam and we strive to keep our 200-125 dumps up-to-date and reliable on a consistent basis. Our exam preparation material is rich in variety. We offer 200-125 PDF format and 200-125 practice test with free VCE player. That’s the reason why many candidates choose Lead2pass.

2017 Cisco 200-125 (All 929 Q&As) exam dumps (PDF&VCE) from Lead2pass:

https://www.lead2pass.com/200-125.html [100% Exam Pass Guaranteed]