300-360 Dumps 300-360 Exam Questions 300-360 New Questions 300-360 PDF 300-360 VCE Cisco

[Full Version] 2016 Updated Lead2pass Cisco 300-360 Exam Questions (31-40)

2016 November Cisco Official New Released 300-360 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

2016 timesaving comprehensive guides for Cisco 300-360 exam: Using latest released Lead2pass 300-360 exam questions, quickly pass 300-360 exam 100%! Following questions and answers are all new published by Cisco Official Exam Center!

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/300-360.html

QUESTION 31
After the completion of a site survey with Ekahau Site Survey tool, using the default color palette, it is noted that multiple areas are shown as white on the heat map when viewing 5 GHz signal strength data. What does this indicate about the signal strength?

A.    The area is below the minimum threshold configured on the tool.
B.    The area is below the detectable level and indicates no RF signal.
C.    The area is below -100 dBm at coverage cell edge.
D.    The area is below -67 dBm at coverage cell edge.

Answer: A

QUESTION 32
An engineer must design wireless coverage in thick-walled stairwells. Which information should the engineer refer to when determining where APs can be installed?

A.    Local or National Building Code
B.    IEEE
C.    BICSI TDMM
D.    Cisco Hardware Installation Guide

Answer: D

QUESTION 33
An engineer is performing a predictive wireless design for a medical treatment environment, which requires data and voice services. Which of the following is a requirement for the design?

A.    overlapping -72 dBm coverage from two access points
B.    overlapping -67 dBm coverage from two access points
C.    continuous -67 dBm coverage from one access point
D.    continuous -72 dBm coverage from one access point

Answer: C

QUESTION 34
A network engineer is preparing for an office site survey with a height of 2.5 meters. Which three components are recommended to complete the survey? (Choose three.)

A.    Use APs with external antennas.
B.    Use DoS attack on APs while measuring the throughput.
C.    Use APs with built-in antennas.
D.    Use a battery pack to power APs.
E.    Use a drawing of the office space to draw AP and client placements.
F.    Use APs with directional antennas.

Answer: CDE

QUESTION 35
An engineer is planning for a 24 Mbps data rate for a new installation.
What is the coverage area from the AP if the environment and other factors are not taken into consideration?

A.    225 feet
B.    80 feet
C.    150 feet
D.    100 feet

Answer: D

QUESTION 36
Which two options describe best practices that must be completed after a wireless installation is finished? (Choose two.)

A.    Make sure that there are no spaces between the devices on the rack that the Wireless Lan Controller isinstalled.
B.    Consult with the customer to ensure that the IT staff has a complete set of design and installationdocuments.
C.    Make sure the customer is aware that they should consider purchasing a support contract immediately afterthe installation is complete.
D.    Spend time with the customer to show them the controller GUI and inform them how they can reach theCisco TAC if they have any problems.
E.    Test all the customer’s wireless devices and applications to ensure they are working properly.

Answer: BE

QUESTION 37
A customer is deploying a Greenfield 802.11ac network on a floor that will support approximately 300 wireless devices. Which setting needs to be changed on Prime Infrastructure Planning Tool in order to predict the amount of access points the customer needs to service the new floor?

A.    Data Coverage Support Margin
B.    Demand Settings
C.    Add AP Field
D.    802.11n Protocol Support

Answer: B
Explanation:
http://www.cisco.com/c/en/us/td/docs/wireless/prime_infrastructure/1- 2/configuration/guide/pi_12_cg/maps.html#pgfId-1671104

QUESTION 38
What is the recommended minimum speed at the edge of the cells in an 802.11g network for a good Cisco VoWLAN deployment?

A.    11 Mb/s
B.    36 Mb/s
C.    12 Mb/s
D.    18 Mb/s

Answer: C

QUESTION 39
An engineer is conducting a location readiness test and wants a selected point to be considered location-ready. Which three possible configurations reflect the minimum number of APs needed? (Choose three.)

A.    One AP is resident in each quadrant surrounding the point-in-question.
B.    One AP per 1400 sq. ft. on the map.
C.    Two APs are resident in each quadrant surrounding the point-in- question.
D.    Four APs are deployed on the floor.
E.    Three APs are within 70 feet (21 meters) of the point-in- question
F.    Three APs are deployed on the floor.

Answer: ADE

QUESTION 40
A network engineer is configuring QoS with a DSCP value of 46. To which queue must the CoS be mapped for priority queuing of the voice frames?

A.    1
B.    2
C.    5
D.    4
E.    3

Answer: C

Lead2pass is confident that our NEW UPDATED 300-360 exam questions and answers are changed with Cisco Official Exam Center. If you cannot pass 300-360 exam, never mind, we will return your full money back! Visit Lead2pass exam dumps collection website now and download 300-360 exam dumps instantly today!

300-360 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDaV9QUWlYNkdKU1E

2016 Cisco 300-360 exam dumps (All 72 Q&As) from Lead2pass:

http://www.lead2pass.com/300-360.html [100% Exam Pass Guaranteed]